Sennheiser HD 560S

Decision Profile · L2 · documentation + editorial inference

Sennheiser HD 560S

Open-back wired dynamic headphones with a 120-ohm transducer and removable analogue lead.

Evidence checked / updated: 2026-10-11. Manufacturer claims and editorial system-fit assessment. No SoundPath Lab listening or measurement test.

Verified documentation

• Electrical reference: 120 ohms; 110 dB at 1 kHz/1 V RMS.
• Manufacturer acoustic specifications: 6 Hz–38 kHz; <0.05% THD at 1 kHz/90 dB SPL.
• Cable and transducer: Current page describes 1.8 m 3.5 mm cable with 6.3 mm adapter; 280 g listed.

Best for

quiet-room editing/reference work accepting an open earcup

Avoid if

commuting isolation, Bluetooth or hands-free microphone functions

Limits and unknowns

These are passive wired headphones, not USB/Bluetooth receivers. Frequency extent is a vendor range without a complete response curve. Comfort, seal, tonal preference and maximum safe level were not tested.

Current verdict

Conditional shortlist for quiet-room editing/reference work accepting an open earcup. The recommendation depends on the documented system conditions, not an independent sound-quality ranking.

Why it fits

Open-back wired dynamic headphones with a 120-ohm transducer and removable analogue lead. This assessment is an editorial inference from the documented topology.

What it can replace

Can consolidate the functions stated in the profile when the source, load and control path meet the conditions below. The useful replacement is a function or connection gap, rather than an assumed improvement in sound.

What it cannot replace

commuting isolation, Bluetooth or hands-free microphone functions

What SoundPath Lab tested

SoundPath Lab checked primary-source model identity, the stated interfaces and conditions, and this decision profile. No device was listened to, measured, installed, firmware-retested or endurance-tested for this review.

What remains untested

Actual sound preference, noise with your headphones or speakers, software behavior, room results, connection stability and long-term reliability remain untested. Manufacturer measurements below are not SPL measurements.

System conditions

Use a suitable headphone amplifier, not a speaker terminal. Match the actual connector and cable wiring, start at low volume, and assess voltage/noise using the stated sensitivity reference. Open-back models leak sound; IEM performance depends on the ear-tip seal.

Alternatives by need

HD 550 is the direct alternative for construction/cable/load differences; HD 650 changes cost or isolation needs. Listen for personal fit before assuming an upgrade from specifications.

Keep or upgrade

Keep a working system if it already provides the connections and level you need. Consider this model only if its documented role solves the specific need described above; check the alternatives and all remaining costs before changing equipment.

When to reassess

Reassess after a material manual or firmware change, an independently reproduced issue, a hardware revision, or a documented change in service or repair availability. A routine update does not prove that an existing issue is resolved.

Ownership evidence

No six-month ownership study was performed. Battery wear, pad or stylus replacement, service dependence and local repair access should be evaluated for the actual use case. No future reliability outcome is predicted.

Firmware, manual and support

This documented signal path is analogue and does not need an audio app or firmware subscription. The linked model documentation does not promise perpetual parts supply; check local repair, replaceable consumables and warranty conditions before purchase.

Launch day, globally uniform price, local authorized stock, repair turnaround and guaranteed support end date were not established in this review. Regional store offers are not global availability. No defect-free or six-month reliability claim is made.

Related records

• Sennheiser HD 550
• Sennheiser HD 650
• Product directory
• Product issues and limitations
• Firmware and app tracker
• Truth and risks

Primary sources

• https://us.sennheiser-hearing.com/products/hd-560s — official documentation, checked 2026-10-11

Revision record

2026-10-11 — Promoted from L1 to L2 after full Decision Profile review. Stable product identity retained; source conflicts and untested behavior remain visible. L2 is evidence coverage, not independent test acceptance or automatic recommendation.